FEATURE TYPE (FEATURETYPE) [String;Yes(No);32;0;0;Pop_Req] The code which identifies the type of topographic feature represented.

Conveyor

FEATURE RELIABILITY DATE (FEATURERELIABILITY) [Date;Yes;36;0;0;Pop_Req] The reliability date of the spatial object; Date to be adjusted only during spatial change or verification of an existing feature location or the capture of a new feature (see (see Section 1 Chapter 3.6); Most Recent Reliability Date of Revision Source Material (or Base Material/digital data for initial capture) used for Spatial Verification

FEATURE SOURCE (FEATURESOURCE) [String;Yes;50;0;0;Pop_Req] This primary source used to determine the spatial location of a feature.

ATTRIBUTE RELIABILITY DATE (ATTRIBUTERELIABILITY) [Date;Yes;36;0;0;Pop_Req] The reliability date of the attribute object; Date to be adjusted only during attribute change or verification of an existing feature's item values or the capture of a new feature (see Section 1 Chapter 3.6) ; Most Recent Reliability Date of Revision Source Material (or Base Material/digital data for initial capture) used for Attribute Verification.

ATTRIBUTE SOURCE (ATTRIBUTESOURCE) [String;Yes;50;0;0;Pop_Req] The primary source used to populate the attribute fields of a feature.

PLANIMETRIC ACCURACY (PLANIMETRICACCURACY) [SmallInteger;Yes(No);0;4;0;Pop_Req] The standard deviation of the horizontal positional accuracy. (See Section 1 Chapter 3.7 Positional Accuracy for more information);

REVISED DATE (REVISED) [Date;Yes;36;0;0;Pop_Aut] Date of creation or subsequent revision of the feature in the database. This field will be entered/edited automatically by GEOSCIENCE AUSTRALIA.

STAKEHOLDERID (STKEHDRID) [String;Yes;250;0;0;Pop_Wk] This is the id used by GA stakeholders or collaborators to identify the link between data maintained, captured or held by GA and their own datasets.

STAKEHOLDER NAME RELATED TO ID ENTRY (STKEHDRNAME) [String;Yes;250;0;0;Pop_Wk] This is the name of stakeholders or collaborators from whom the stakeholderid has been derived and data link is maintained.

TEXT NOTE (TEXTNOTE) [String;Yes;50;0;0;Pop_Dep] Descriptive note to appear on map. Text Note field should be added when directed in the Geodatabase Rules or if descriptive information is known about a feature that is not covered by any other item in the feature class and expands on the definition of the feature.

DIMENSION (DIMENSION) [Double;Yes;0;15;0;Pop_Dep] This is the dimension of the linear feature in metres or the polygon feature in square metres as measured in the MGA94 projection of the appropriate zone. This field will be populated internally by Geoscience Australia and should not be altered in any form by producers.

EDIT CODE (EDITCODE) [SmallInteger;Yes;0;5;0;Pop_Dep] A number allowed for ease of symbology of errors or production notes. This code is for production purposes and therefore for producers internal use only and will not be validated.

SYMBOL FOR 100 000 PRODUCTS (SYMBOL100K) [Integer; Yes; 4; 0; 0; Pop_Dep] For Applicable Symbol numbers including core values see attached link; (See RepresentationFieldsTables_Industry.html)

SYMBOL FOR 250 000 PRODUCTS (SYMBOL250K) [Integer; Yes; 4; 0; 0; Pop_Dep] For Applicable Symbol numbers including core values see attached link; (See RepresentationFieldsTables_Industry.html)

SYMBOL FOR 1 000 000 PRODUCTS (SYMBOLWAC1Mil) [Integer; Yes; 4; 0; 0; Pop_Dep] For Applicable Symbol numbers including core values see attached link; (See RepresentationFieldsTables_Industry.html)

GLOBAL IDENTIFIER (GlobalID) [Global ID;Yes;Pop_Aut] A unique system generated Global Identifier. This field will be entered/edited automatically by GEOSCIENCE AUSTRALIA.

General - All Scales

Size and any other selection criteria apply to all feature occurrences. All feature occurrences existing in the base material/digital data or NTDB meeting the minimum size for inclusion will be retained unless there is clear evidence they no longer exist.

The name of a conveyor will be held in the TextNote field.

General - All Scales

Conveyor features inside Built Up Areas will not be depicted.

General - All Scales

All conveyors are to have an accompanying descriptive note 'conveyor' unless the word 'conveyor' is included in the name.

Conveyors will be masked where black type unavoidably overprints the feature. The break measurement will be 0.2 mm on either side of the type where it crosses the feature. (Note: the feature will be masked only on the map and will be complete in the data.)

Aerial Cableway, Mine Area, Mine Point

GEODATA TOPO250K, NTMS 100K, NTMS 250K

ANNOTATION CLASS IDENTIFER (ANNOTATIONCLASSID) [Integer;Yes;0;10;0;Pop_Aut] This is the Annotation Class Identifier which is used to define annotation subtypes.

The following annotation classes exist in IndustryAnno;
ArialNarrow6ptCenter
ArialNarrow6ptItalicCenter
ArialNarrow6ptItalicLeft
ArialNarrow6ptItalicRight
ArialNarrow6ptLeft
ArialNarrow6ptRight
ArialNarrow7ptCenter
ArialNarrow7ptLeft
ArialNarrow7ptRight

FEATURE (FEATURE) [String;Yes;32;0;0;Pop_Req] The code which identifies the class of topographic feature represented by the annotation. This field must be a legitimate feature class name.

Acceptable Domain Entries from dm_IndustryFCs;
Conveyors
MineAreas
MinePoints
PetroleumWells
StorageTanks

REVISED DATE (REVISED) [Date;Yes;36;0;0;Pop_Aut] Date of creation or subsequent revision of the feature in the database. This field will be entered/edited automatically by GEOSCIENCE AUSTRALIA.

EDIT CODE (EDITCODE) [SmallInteger;Yes;0;5;0;Pop_Dep] A number allowed for ease of symbology of errors or production notes. This code is for production purposes and therefore for producers internal use only and will not be validated.

GLOBAL IDENTIFIER (GlobalID) [Global ID;Yes;Pop_Aut] A unique system generated Global Identifier. This field will be entered/edited automatically by GEOSCIENCE AUSTRALIA.

General - All Scales

No feature type field exists for this annotation feature class. The feature type has only been included throughout the specification documentation for ease of reference.

Only Annotation associated with, or derived from, entities in feature classes grouped within the Industry feature dataset should exist within the IndustryAnno feature class.

Wherever possible annotation should be stored using the subclasses indicated under AnnotationClassID. Annotation stored as inline text should be kept to a minimum.

Type for large polygons and long linear features may be held in an annotation feature for each word to allow for spacing and differences in orientation, see Section 2 chapter 4.

Annotation should not contain any HTML tags within the blob element, nor should it contain any special characters.

Editing and placement of Annotation should be conducted in the appropriate MGA 1994 zone to ensure the spatial position of type on the map face can be correctly represented.

Annotation should only occur where the associated feature either has a sufficient dimension size or Upperscale value to be shown at 1:100 000 scale or a smaller scale/larger extent (eg 1:250 000, 1:1 000 000)

Section 2 Chapter 5, 9

NTMS 100K

ANNOTATION CLASS IDENTIFER (ANNOTATIONCLASSID) [Integer;Yes;0;10;0;Pop_Aut] This is the Annotation Class Identifier which is used to define annotation subtypes.

The following annotation classes exist in IndustryAnno;
ArialNarrow5ptCenter
ArialNarrow5ptLeft
ArialNarrow6ptCenter
ArialNarrow6ptItalicCenter
ArialNarrow6ptItalicLeft
ArialNarrow6ptItalicRight
ArialNarrow6ptLeft
ArialNarrow6ptRight
ArialNarrow7ptCenter
ArialNarrow7ptLeft
ArialNarrow7ptRight

FEATURE (FEATURE) [String;Yes;32;0;0;Pop_Req] The code which identifies the class of topographic feature represented by the annotation. This field must be a legitimate feature class name.

Acceptable Domain Entries from dm_IndustryFCs;
Conveyors
MineAreas
MinePoints
PetroleumWells
StorageTanks

REVISED DATE (REVISED) [Date;Yes;36;0;0;Pop_Aut] Date of creation or subsequent revision of the feature in the database. This field will be entered/edited automatically by GEOSCIENCE AUSTRALIA.

EDIT CODE (EDITCODE) [SmallInteger;Yes;0;5;0;Pop_Dep] A number allowed for ease of symbology of errors or production notes. This code is for production purposes and therefore for producers internal use only and will not be validated.

GLOBAL IDENTIFIER (GlobalID) [Global ID;Yes;Pop_Aut] A unique system generated Global Identifier. This field will be entered/edited automatically by GEOSCIENCE AUSTRALIA.

General - All Scales

No feature type field exists for this annotation feature class. The feature type has only been included throughout the specification documentation for ease of reference.

Only Annotation associated with, or derived from, entities in feature classes grouped within the Industry feature dataset should exist within the IndustryAnno feature class.

Wherever possible annotation should be stored using the subclasses indicated under AnnotationClassID. Annotation stored as inline text should be kept to a minimum.

Type for large polygons and long linear features may be held in an annotation feature for each word to allow for spacing and differences in orientation, see Section 2 chapter 4.

Annotation should not contain any HTML tags within the blob element, nor should it contain any special characters.

Editing and placement of Annotation should be conducted in the appropriate MGA 1994 zone to ensure the spatial position of type on the map face can be correctly represented.

Annotation should only occur where the associated feature either has a sufficient dimension size or Upperscale value to be shown at 1:250 000 scale or a smaller scale/larger extent (eg 1:1 000 000, 1:5 000 000)

Section 2 Chapter 5, 10

NTMS 100K

ANNOTATION CLASS IDENTIFER (ANNOTATIONCLASSID) [Integer;Yes;0;10;0;Pop_Aut] This is the Annotation Class Identifier which is used to define annotation subtypes.

The following annotation classes exist in IndustryAnno;
ArialNarrow6ptCenter
ArialNarrow6ptItalicCenter
ArialNarrow6ptItalicLeft
ArialNarrow6ptItalicRight
ArialNarrow6ptLeft
ArialNarrow6ptRight
ArialNarrow7ptCenter
ArialNarrow7ptLeft
ArialNarrow7ptRight
ArialNarrow7ptItalicCenter
ArialNarrow7ptItalicLeft
ArialNarrow7ptItalicRight

FEATURE (FEATURE) [String;Yes;32;0;0;Pop_Req] The code which identifies the class of topographic feature represented by the annotation. This field must be a legitimate feature class name.

Acceptable Domain Entries from dm_IndustryFCs;
Conveyors
MineAreas
MinePoints
PetroleumWells
StorageTanks

REVISED DATE (REVISED) [Date;Yes;36;0;0;Pop_Aut] Date of creation or subsequent revision of the feature in the database. This field will be entered/edited automatically by GEOSCIENCE AUSTRALIA.

EDIT CODE (EDITCODE) [SmallInteger;Yes;0;5;0;Pop_Dep] A number allowed for ease of symbology of errors or production notes. This code is for production purposes and therefore for producers internal use only and will not be validated.

GLOBAL IDENTIFIER (GlobalID) [Global ID;Yes;Pop_Aut] A unique system generated Global Identifier. This field will be entered/edited automatically by GEOSCIENCE AUSTRALIA.

General - All Scales

No feature type field exists for this annotation feature class. The feature type has only been included throughout the specification documentation for ease of reference.

Only Annotation associated with, or derived from, entities in feature classes grouped within the Industry feature dataset should exist within the IndustryAnno feature class.

Wherever possible annotation should be stored using the subclasses indicated under AnnotationClassID. Annotation stored as inline text should be kept to a minimum.

Type for large polygons and long linear features may be held in an annotation feature for each word to allow for spacing and differences in orientation, see Section 2 chapter 4.

Annotation should not contain any HTML tags within the blob element, nor should it contain any special characters.

Editing and placement of Annotation should be conducted in the appropriate Lambert Conic Conformal Projection (with two standard parallels and a central meridian per each chart's requirements) to ensure the spatial position of type on the map face can be correctly represented.

Annotation should only occur where the associated feature either has a sufficient dimension size or Upperscale value to be shown at 1:1 000 000 scale or a smaller scale/larger extent (eg 1:2 500 000, 1:10 000 000)

Section 2 Chapter 5, 11

NTMS 100K

FEATURE TYPE (FEATURETYPE) [String;Yes(No);32;0;0;Pop_Req] The code which identifies the type of topographic feature represented.

Mine Area

NAME (NAME) [String;Yes;60;0;0;Pop_Dep]

The name of the Mine. This item should be populated where name is known.

FEATURE RELIABILITY DATE (FEATURERELIABILITY) [Date;Yes;36;0;0;Pop_Req] The reliability date of the spatial object; Date to be adjusted only during spatial change or verification of an existing feature location or the capture of a new feature (see (see Section 1 Chapter 3.6); Most Recent Reliability Date of Revision Source Material (or Base Material/digital data for initial capture) used for Spatial Verification

FEATURE SOURCE (FEATURESOURCE) [String;Yes;50;0;0;Pop_Req] This primary source used to determine the spatial location of a feature.

ATTRIBUTE RELIABILITY DATE (ATTRIBUTERELIABILITY) [Date;Yes;36;0;0;Pop_Req] The reliability date of the attribute object; Date to be adjusted only during attribute change or verification of an existing feature's item values or the capture of a new feature (see Section 1 Chapter 3.6) ; Most Recent Reliability Date of Revision Source Material (or Base Material/digital data for initial capture) used for Attribute Verification.

ATTRIBUTE SOURCE (ATTRIBUTESOURCE) [String;Yes;50;0;0;Pop_Req] The primary source used to populate the attribute fields of a feature.

PLANIMETRIC ACCURACY (PLANIMETRICACCURACY) [SmallInteger;Yes(No);0;4;0;Pop_Req] The standard deviation of the horizontal positional accuracy. (See Section 1 Chapter 3.7 Positional Accuracy for more information);

REVISED DATE (REVISED) [Date;Yes;36;0;0;Pop_Aut] Date of creation or subsequent revision of the feature in the database. This field will be entered/edited automatically by GEOSCIENCE AUSTRALIA.

STAKEHOLDERID (STKEHDRID) [String;Yes;250;0;0;Pop_Wk] This is the id used by GA stakeholders or collaborators to identify the link between data maintained, captured or held by GA and their own datasets.

STAKEHOLDER NAME RELATED TO ID ENTRY (STKEHDRNAME) [String;Yes;250;0;0;Pop_Wk] This is the name of stakeholders or collaborators from whom the stakeholderid has been derived and data link is maintained.

TEXT NOTE (TEXTNOTE) [String;Yes;50;0;0;Pop_Dep] Descriptive note to appear on map. Text Note field should be added when directed in the Geodatabase Rules or if descriptive information is known about a feature that is not covered by any other item in the feature class and expands on the definition of the feature.

DIMENSION (DIMENSION) [Double;Yes;0;15;0;Pop_Dep] This is the dimension of the linear feature in metres or the polygon feature in square metres as measured in the MGA94 projection of the appropriate zone. This field will be populated internally by Geoscience Australia and should not be altered in any form by producers.

EDIT CODE (EDITCODE) [SmallInteger;Yes;0;5;0;Pop_Dep] A number allowed for ease of symbology of errors or production notes. This code is for production purposes and therefore for producers internal use only and will not be validated.

SYMBOL FOR 100 000 PRODUCTS (SYMBOL100K) [Integer; Yes; 4; 0; 0; Pop_Dep] For Applicable Symbol numbers including core values see attached link; (See RepresentationFieldsTables_Industry.html)

SYMBOL FOR 250 000 PRODUCTS (SYMBOL250K) [Integer; Yes; 4; 0; 0; Pop_Dep] For Applicable Symbol numbers including core values see attached link; (See RepresentationFieldsTables_Industry.html)

SYMBOL FOR 1 000 000 PRODUCTS (SYMBOLWAC1Mil) [Integer; Yes; 4; 0; 0; Pop_Dep] For Applicable Symbol numbers including core values see attached link; (See RepresentationFieldsTables_Industry.html)

SYMBOL FOR 2 500 000 PRODUCTS (SYMBOL2_5Mil) [Integer; Yes; 4; 0; 0; Pop_Dep] For Applicable Symbol numbers including core values see attached link; (See RepresentationFieldsTables_Industry.html)

GLOBAL IDENTIFIER (GlobalID) [Global ID;Yes;Pop_Aut] A unique system generated Global Identifier. This field will be entered/edited automatically by GEOSCIENCE AUSTRALIA.

General - All Scales

Size and any other selection criteria apply to all feature occurrences. All feature occurrences existing in the base material/digital data or NTDB meeting the minimum size for inclusion will be retained unless there is clear evidence they no longer exist.

All mines will be represented either as a Mine Area or as a Mine Point.

Existing features below the minimum data capture size for a Mine Area will be retained in the same geometry as captured in the base material/digital data (eg Mine Area or Mine Point). The only exception is existing features smaller than the minimum size for inclusion which will be represented as Mine Points.

New features smaller than the minimum size for data capture will be represented as Mine Points. (see Mine Point).

Mine Areas are NOT to be textnoted with descriptive text indicating the mineral which is extracted.

Tailings dumps not adjacent to a mine will be textnoted 'tailings'.

Abandoned mines will be labelled 'abandoned'.

Where an Open Cut Mine Area is no longer associated with any mining activity and has since filled with water to the extent that it is now a permanent 'lake type feature', then it should be captured as a Lake. This is in spite of the feature type definition saying it must be naturally occurring as it is now a key hydrological entity not held behind a dam structure.

Where a mine, upon review of imagery, appears to have undergone rehabilitation, a producer should request clarification (via an action request) from Geoscience Australia on how to proceed.

A textnote may be included where its known function is expanded beyond that of the strict definition of a Mine Area, and where it would provide additional meaningful detail to the map. A descriptive note of "mine" is not to be used. Where applicable textnotes should be ordered so that status information such as 'abandoned' or 'disused' follows the known function descriptions e.g. 'tailing dumps disused'

For SYMBOLWAC1Mil, Mine Areas equal to or greater than 220 000 sq m and less than 2 250 000 sq m should be represented as point mines (eg 3543 - Mine Area to Pt). Mine Areas equal to or greater than 2 250 000 sq m should be represented as polygon mines (eg 102 - Mine Area).

For SYMBOL2_5Mil, Mine Areas equal to or greater than 20 250 000 sq m should be represented as polygon mines (eg 102 - Mine Area). No mine areas should be represented as point features.

General - All Scales

The following cannot overlap or appear inside Mine Areas;
Other Mine Areas, Mine Points

General - All Scales

The following cannot overlap or appear inside Mine Areas;
AircraftFacilityPoint, AircraftFacilityArea, Airport, Built Up Area, Contours other than of type connector standard, Watercourses, Spot Elevations, Sea, any polygon in the Waterbodies datasets.

General - All Scales

Mine Areas are NOT to be labelled with descriptive text indicating the mineral which is extracted.

Tailings dumps not adjacent to a mine will be labelled 'tailings'.

Abandoned mines will be labelled 'abandoned'.

A descriptive note may be included where its known function is expanded beyond that of the strict definition an open cut mine, and where it would provide additional meaningful detail to the map. A descriptive note of "mine" is not to be used.

Mine Point, Crater, Sand Area, Sand Dune, Settling Pond

Section 3 Chapters 5.11.1, 5.11.2, 5.18 and 5.19
Appendix U Chapter 2.4

GEODATA LITE TOPO100K, GEODATA TOPO250K, NTMS 100K, NTMS 250K

FEATURE TYPE (FEATURETYPE) [String;Yes(No);32;0;0;Pop_Req] The code which identifies the type of topographic feature represented.

Mine Point

NAME (NAME) [String;Yes;60;0;0;Pop_Dep]

The name of the Mine. This item should be populated where name is known.

FEATURE RELIABILITY DATE (FEATURERELIABILITY) [Date;Yes;36;0;0;Pop_Req] The reliability date of the spatial object; Date to be adjusted only during spatial change or verification of an existing feature location or the capture of a new feature (see (see Section 1 Chapter 3.6); Most Recent Reliability Date of Revision Source Material (or Base Material/digital data for initial capture) used for Spatial Verification

FEATURE SOURCE (FEATURESOURCE) [String;Yes;50;0;0;Pop_Req] This primary source used to determine the spatial location of a feature.

ATTRIBUTE RELIABILITY DATE (ATTRIBUTERELIABILITY) [Date;Yes;36;0;0;Pop_Req] The reliability date of the attribute object; Date to be adjusted only during attribute change or verification of an existing feature's item values or the capture of a new feature (see Section 1 Chapter 3.6) ; Most Recent Reliability Date of Revision Source Material (or Base Material/digital data for initial capture) used for Attribute Verification.

ATTRIBUTE SOURCE (ATTRIBUTESOURCE) [String;Yes;50;0;0;Pop_Req] The primary source used to populate the attribute fields of a feature.

PLANIMETRIC ACCURACY (PLANIMETRICACCURACY) [SmallInteger;Yes(No);0;4;0;Pop_Req] The standard deviation of the horizontal positional accuracy. (See Section 1 Chapter 3.7 Positional Accuracy for more information);

REVISED DATE (REVISED) [Date;Yes;36;0;0;Pop_Aut] Date of creation or subsequent revision of the feature in the database. This field will be entered/edited automatically by GEOSCIENCE AUSTRALIA.

STAKEHOLDERID (STKEHDRID) [String;Yes;250;0;0;Pop_Wk] This is the id used by GA stakeholders or collaborators to identify the link between data maintained, captured or held by GA and their own datasets.

STAKEHOLDER NAME RELATED TO ID ENTRY (STKEHDRNAME) [String;Yes;250;0;0;Pop_Wk] This is the name of stakeholders or collaborators from whom the stakeholderid has been derived and data link is maintained.

UPPER SCALE OF DATA UTILISATION (UPPERSCALE) [Integer;Yes;0;8;0;Pop_Dep] Upper Scale for which the entity should be considered suitable either in its current representation or in a different geometry representation;

Acceptable Domain Entries from dm_UpperScale;
0
25000
50000
100000
250000
1000000

UPPER SCALE CERTAINTY (USCERTAINTY) [String;Yes;25;0;0;Pop_Dep] Classification of upper scale certainty;

Acceptable Domain Entries from dm_USCertainty;
Automatically Assigned
Definite
Indefinite
Undefined

TEXT NOTE (TEXTNOTE) [String;Yes;50;0;0;Pop_Dep] Descriptive note to appear on map. Text Note field should be added when directed in the Geodatabase Rules or if descriptive information is known about a feature that is not covered by any other item in the feature class and expands on the definition of the feature.

EDIT CODE (EDITCODE) [SmallInteger;Yes;0;5;0;Pop_Dep] A number allowed for ease of symbology of errors or production notes. This code is for production purposes and therefore for producers internal use only and will not be validated.

SYMBOL FOR 100 000 PRODUCTS (SYMBOL100K) [Integer; Yes; 4; 0; 0; Pop_Dep] For Applicable Symbol numbers including core values see attached link; (See RepresentationFieldsTables_Industry.html)

SYMBOL FOR 250 000 PRODUCTS (SYMBOL250K) [Integer; Yes; 4; 0; 0; Pop_Dep] For Applicable Symbol numbers including core values see attached link; (See RepresentationFieldsTables_Industry.html)

SYMBOL FOR 1 000 000 PRODUCTS (SYMBOLWAC1Mil) [Integer; Yes; 4; 0; 0; Pop_Dep] For Applicable Symbol numbers including core values see attached link; (See RepresentationFieldsTables_Industry.html)

GLOBAL IDENTIFIER (GlobalID) [Global ID;Yes;Pop_Aut] A unique system generated Global Identifier. This field will be entered/edited automatically by GEOSCIENCE AUSTRALIA.

General - All Scales

Size and any other selection criteria apply to all feature occurrences. All feature occurrences existing in the base material/digital data or NTDB meeting the minimum size for inclusion will be retained unless there is clear evidence they no longer exist.

All mines will be represented either as a Mine Area or as a Mine Point.

Existing features below the minimum data capture size for a Mine Area will be retained in the same geometry as captured in the base material/digital data (eg Mine Area or Mine Point). The only exception is existing features smaller than the minimum size for inclusion of a Mine Area which will be represented as Mine Points.

New features smaller than the minimum size for data capture of a Mine Area will be represented as Mine Points.

Indicative reference material for mines will be supplied. However, mines will be retained from the existing base material/digital data unless there is clear evidence they no longer exist and new mines will only be added when their position can be verified on the imagery or other reliable reference or supporting material.

This feature may be used to indicate a small group of mines.

Abandoned mines will be textnoted 'abandoned'

Where a mine, upon review of imagery, appears to have undergone rehabilitation, a producer should request clarification (via an action request) from Geoscience Australia on how to proceed.

Mine Points may have a textnote where its known function is expanded beyond that of the strict definition of a Mine Point and where it provides additional meaningful detail to the map e.g. clay pit, gravel pit, mining area unless the words clay pit, gravel pit, mining area, etc are included in the name. A descriptive note of "mine" is not to be used.

General - All Scales

Mine Points cannot overlap;
Mine Areas

General - All Scales

Mine Points cannot overlap BuildingAreas Ruin (feature class).

General - All Scales

Abandoned mines will be labelled 'abandoned'

Mine Points may have a textnote where its known function is expanded beyond that of the strict definition of a Mine Point and where it provides additional meaningful detail to the map e.g. clay pit, gravel pit, mining area unless the words clay pit, gravel pit, mining area, etc are included in the name. A descriptive note of "mine" is not to be used.

Petroleum Well, Mine Area, Settling Pond

Section 3 Chapters 5.3, 5.11.1
Appendix U Chapter 2.4

GEODATA TOPO250K, NTMS 100K, NTMS 250K

FEATURE TYPE (FEATURETYPE) [String;Yes(No);32;0;0;Pop_Req] The code which identifies the type of topographic feature represented.

Petroleum Well

FEATURE RELIABILITY DATE (FEATURERELIABILITY) [Date;Yes;36;0;0;Pop_Req] The reliability date of the spatial object; Date to be adjusted only during spatial change or verification of an existing feature location or the capture of a new feature (see (see Section 1 Chapter 3.6); Most Recent Reliability Date of Revision Source Material (or Base Material/digital data for initial capture) used for Spatial Verification

FEATURE SOURCE (FEATURESOURCE) [String;Yes;50;0;0;Pop_Req] This primary source used to determine the spatial location of a feature.

ATTRIBUTE RELIABILITY DATE (ATTRIBUTERELIABILITY) [Date;Yes;36;0;0;Pop_Req] The reliability date of the attribute object; Date to be adjusted only during attribute change or verification of an existing feature's item values or the capture of a new feature (see Section 1 Chapter 3.6) ; Most Recent Reliability Date of Revision Source Material (or Base Material/digital data for initial capture) used for Attribute Verification.

ATTRIBUTE SOURCE (ATTRIBUTESOURCE) [String;Yes;50;0;0;Pop_Req] The primary source used to populate the attribute fields of a feature.

PLANIMETRIC ACCURACY (PLANIMETRICACCURACY) [SmallInteger;Yes(No);0;4;0;Pop_Req] The standard deviation of the horizontal positional accuracy. (See Section 1 Chapter 3.7 Positional Accuracy for more information);

REVISED DATE (REVISED) [Date;Yes;36;0;0;Pop_Aut] Date of creation or subsequent revision of the feature in the database. This field will be entered/edited automatically by GEOSCIENCE AUSTRALIA.

STAKEHOLDERID (STKEHDRID) [String;Yes;250;0;0;Pop_Wk] This is the id used by GA stakeholders or collaborators to identify the link between data maintained, captured or held by GA and their own datasets.

STAKEHOLDER NAME RELATED TO ID ENTRY (STKEHDRNAME) [String;Yes;250;0;0;Pop_Wk] This is the name of stakeholders or collaborators from whom the stakeholderid has been derived and data link is maintained.

TEXT NOTE (TEXTNOTE) [String;Yes;50;0;0;Pop_Dep] Descriptive note to appear on map. Text Note field should be added when directed in the Geodatabase Rules or if descriptive information is known about a feature that is not covered by any other item in the feature class and expands on the definition of the feature.

EDIT CODE (EDITCODE) [SmallInteger;Yes;0;5;0;Pop_Dep] A number allowed for ease of symbology of errors or production notes. This code is for production purposes and therefore for producers internal use only and will not be validated.

SYMBOL FOR 100 000 PRODUCTS (SYMBOL100K) [Integer; Yes; 4; 0; 0; Pop_Dep] For Applicable Symbol numbers including core values see attached link; (See RepresentationFieldsTables_Industry.html)

SYMBOL FOR 250 000 PRODUCTS (SYMBOL250K) [Integer; Yes; 4; 0; 0; Pop_Dep] For Applicable Symbol numbers including core values see attached link; (See RepresentationFieldsTables_Industry.html)

SYMBOL FOR 1 000 000 PRODUCTS (SYMBOLWAC1Mil) [Integer; Yes; 4; 0; 0; Pop_Dep] For Applicable Symbol numbers including core values see attached link; (See RepresentationFieldsTables_Industry.html)

GLOBAL IDENTIFIER (GlobalID) [Global ID;Yes;Pop_Aut] A unique system generated Global Identifier. This field will be entered/edited automatically by GEOSCIENCE AUSTRALIA.

General - All Scales

All feature occurrences on the base material/digital data or the latest previous edition map will be captured/retained unless there is clear evidence they no longer exist.

These features may be located inland or offshore.

Abandoned wells will only be shown if of landmark significance.

Oil and Gas Platforms associated with offshore Petroleum Wells will be represented using the feature type 'Vertical Obstruction'.

Gas wells are to have an accompanying textnote eg 'gas well', 'oil well' unless the words 'gas well', 'oil well' etc are included in the name.

Abandoned wells will be TextNoted 'abandoned'.

General - All Scales

Petroleum Wells cannot overlap;
BuildingAreas (feature class) or Built Up Area.

General - All Scales

Gas wells are to have an accompanying descriptive note eg 'gas well', 'oil well' unless the words 'gas well', 'oil well', etc are included in the name.

Where a petroleum well and a vertical obstruction are coincident, the petroleum well will be given precedence (ie vertical obstruction given symbol of 2 PointNoDraw) but the feature will be labelled with the vertical obstruction name, height and description (e.g. 'Baraccuda Gas Platform (61m)').

Abandoned wells will have '(abandoned)' at the end of the descriptive note or name.

Mine Point, Vertical Obstruction

GEODATA TOPO250K, NTMS 100K, NTMS 250K

FEATURE TYPE (FEATURETYPE) [String;Yes(No);32;0;0;Pop_Req] The code which identifies the type of topographic feature represented.

Storage Tank

NAME (NAME) [String;Yes;60;0;0;Pop_Dep]

This field is currently not to be populated;

PRODUCT CODE (PRODUCT) [String;Yes;35;0;0;Pop_Dep] Type of product produced or transported;

Acceptable Domain Entries from dm_StorageTankProduct;
Chemical
Fuel
Other
Sewage
Unknown

FEATURE RELIABILITY DATE (FEATURERELIABILITY) [Date;Yes;36;0;0;Pop_Req] The reliability date of the spatial object; Date to be adjusted only during spatial change or verification of an existing feature location or the capture of a new feature (see (see Section 1 Chapter 3.6); Most Recent Reliability Date of Revision Source Material (or Base Material/digital data for initial capture) used for Spatial Verification

FEATURE SOURCE (FEATURESOURCE) [String;Yes;50;0;0;Pop_Req] This primary source used to determine the spatial location of a feature.

ATTRIBUTE RELIABILITY DATE (ATTRIBUTERELIABILITY) [Date;Yes;36;0;0;Pop_Req] The reliability date of the attribute object; Date to be adjusted only during attribute change or verification of an existing feature's item values or the capture of a new feature (see Section 1 Chapter 3.6) ; Most Recent Reliability Date of Revision Source Material (or Base Material/digital data for initial capture) used for Attribute Verification.

ATTRIBUTE SOURCE (ATTRIBUTESOURCE) [String;Yes;50;0;0;Pop_Req] The primary source used to populate the attribute fields of a feature.

PLANIMETRIC ACCURACY (PLANIMETRICACCURACY) [SmallInteger;Yes(No);0;4;0;Pop_Req] The standard deviation of the horizontal positional accuracy. (See Section 1 Chapter 3.7 Positional Accuracy for more information);

REVISED DATE (REVISED) [Date;Yes;36;0;0;Pop_Aut] Date of creation or subsequent revision of the feature in the database. This field will be entered/edited automatically by GEOSCIENCE AUSTRALIA.

STAKEHOLDERID (STKEHDRID) [String;Yes;250;0;0;Pop_Wk] This is the id used by GA stakeholders or collaborators to identify the link between data maintained, captured or held by GA and their own datasets.

STAKEHOLDER NAME RELATED TO ID ENTRY (STKEHDRNAME) [String;Yes;250;0;0;Pop_Wk] This is the name of stakeholders or collaborators from whom the stakeholderid has been derived and data link is maintained.

UPPER SCALE OF DATA UTILISATION (UPPERSCALE) [Integer;Yes;0;8;0;Pop_Dep] Upper Scale for which the entity should be considered suitable either in its current representation or in a different geometry representation;

Acceptable Domain Entries from dm_UpperScale;
0
25000
50000
100000
250000
1000000

UPPER SCALE CERTAINTY (USCERTAINTY) [String;Yes;25;0;0;Pop_Dep] Classification of upper scale certainty;

Acceptable Domain Entries from dm_USCertainty;
Automatically Assigned
Definite
Indefinite
Undefined

TEXT NOTE (TEXTNOTE) [String;Yes;50;0;0;Pop_Dep] Descriptive note to appear on map. Text Note field should be added when directed in the Geodatabase Rules or if descriptive information is known about a feature that is not covered by any other item in the feature class and expands on the definition of the feature.

EDIT CODE (EDITCODE) [SmallInteger;Yes;0;5;0;Pop_Dep] A number allowed for ease of symbology of errors or production notes. This code is for production purposes and therefore for producers internal use only and will not be validated.

SYMBOL FOR 100 000 PRODUCTS (SYMBOL100K) [Integer; Yes; 4; 0; 0; Pop_Dep] For Applicable Symbol numbers including core values see attached link; (See RepresentationFieldsTables_Industry.html)

SYMBOL FOR 250 000 PRODUCTS (SYMBOL250K) [Integer; Yes; 4; 0; 0; Pop_Dep] For Applicable Symbol numbers including core values see attached link; (See RepresentationFieldsTables_Industry.html)

SYMBOL FOR 1 000 000 PRODUCTS (SYMBOLWAC1Mil) [Integer; Yes; 4; 0; 0; Pop_Dep] For Applicable Symbol numbers including core values see attached link; (See RepresentationFieldsTables_Industry.html)

GLOBAL IDENTIFIER (GlobalID) [Global ID;Yes;Pop_Aut] A unique system generated Global Identifier. This field will be entered/edited automatically by GEOSCIENCE AUSTRALIA.

General - All Scales

Size and any other selection criteria apply to all feature occurrences. All feature occurrences existing in the base material/digital data or NTDB will be retained unless there is clear evidence they no longer exist.

Storage tanks will be shown when the features are sufficiently prominent to have a landmark value.

Storage Tanks while generally cylindrical may vary in both shape and size.

Storage tanks are to have an accompanying textnote eg 'storage tanks', 'oil tanks' unless a description is included in the name.

When assigning upperscale values, the proximity between storage tanks at the applicable scale should be considered. Where all storage tanks can not be shown at one location, a selection should be made to retain a representative pattern.

General - All Scales

Storage tanks are to have an accompanying descriptive note eg 'storage tanks', 'oil tanks' unless a description is included in the name.

Vertical Obstruction, Water Tank

Appendix U Chapter 2.3, 2.4

GEODATA TOPO250K, NTMS 100K, NTMS 250K